1
E
N
MB4010T001
AutoScan Color Monitor
English
Operating Instructions...... 2 - 13
Mode d'emploi ……………14 - 25
Français
Appendix
English
Declaration FCC
... A1
Information for Users in the U.S. ... A3
Warranty
... A5
Deutsch
Français
Hinweis / GS
Achtung
... A4
... A6
Declaration FCC
... A2
For Customer Use:
Enter below the Serial No. which is located on the
back of the cabinet. Retain this information for
future reference.
Model No. MB4010T001
Serial No.
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
ATTENTION
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER(OR BACK)
NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
This "bolt of lightning" indicates that uninsulated material
within your unit may cause an electrical shock. For the safety
of everyone, do not remove product covering.
This "exclamation point" calls attention to a feature for which
you should read the enclosed literature carefully to prevent operating
and maintenance problems.
3
E
N
Note: If you experienced your monitor display is changing from color
to mono, it's possible that you are using a non-VESA-DDC-standard
video card. Please consult with your local Philips dealer for more
information.
As an Energy Star Partner, MAGNAVOX, has determined that this
product meets the Energy Star guidelines for energy efficiency.
IBM, IBM PC and Power PC are registered trademarks of International
Business Machines Corporation.
4
E
N
Safety precautions and maintenance
N Disconnect the monitor from the mains supply if the monitor is not
to be used for an extended period of time.
N Do not attempt to remove the back cover, as you will be exposed to
a shock hazard. The back cover should only be removed by qualified
service personnel.
N Do not place objects on top of the monitor cabinet, which could fall
into vents or which could cover them and prevent proper cooling of
the monitor’s electronic devices.
N
Do not expose the monitor to rain or excessive moisture to avoid the
risk of shock or permanent damage to the set.
N Do not use alcohol or ammonia based liquid to clean the monitor. If
necessary, clean with a slightly damp cloth. Disconnect the monitor
from the mains supply before cleaning.
N Consult a service technician if the monitor does not operate normally
when operating instructions of this manual are followed.
Package
Your package includes the following items:
•
•
•
•
The monitor
Pedestal
Power cord
Interface cable (flying-in)
End of life disposal
Your new set contains materials which can be recycled and reused.
Specialized companies can recycle your product to increase the amount
of reusable materials and to minimize the amount of materials to be
disposed of.
Please inform yourself on local regulations on disposal of your old set.
5
E
N
Installation
Important: Please refer to the user’s manuals of your computer and
video adapter to make sure these equipments are properly installed
and configured before installing the monitor.
Positioning / Ventilation
N Avoid exposing the monitor to direct sunlight, stoves or any other
heat sources.
N To prevent overheating, make sure that the ventilation openings of
the monitor are not covered.
N Keep moisture and dust away.
N Keep away from any magnetic objects, such as speakers, electric
motors, transformers, ...etc.
N When positioning this monitor, make sure that the mains plug and
socket are easily accessible.
Pedestal
With the built-in pedestal you can tilt and / or swivel the monitor for a
most comfortable viewing angle.
To fit the pedestal, refer to the illustration on the inside back-cover of
this manual.
6
E
N
Connection
Important: Please make sure the AC power to your computer is
“OFF” before connecting or disconnecting any display peripheral.
Failure to do so may cause serious personal injury as well as
permanent damage to your computer equipments.
Intel Based platform: 386, 486, Pentium, or other compatibles:
•
Connect the monitor to the computer using the supplied interface
cables.
Monitor rear view
1) IBM PC connection
2) Mains connection
VIDEO IN
VIDEIN
2
1
7
E
N
Connection to the mains
(Rear of the monitor)
VIDEO IN
(Mains cord)
Connecting to the mains
This monitor is set to operate at a mains supply of 100-240 volts AC .
If the mains voltage in your home is not between this, consult your
dealer.
Connect one end of the mains cord to the mains socket at the rear of
monitor, and the other end to the mains supply.
The monitor will be operating in power saving mode if you switch on
your monitor without signal input from PC. (Please refer to Power
Management Signalling instruction.)
8
E
N
Front Control locations and functions
For an optimized adjustment of the picture following controls are
available at the front.
POWER.
Press this knob, the green LED lights and the power is ON.
Press this knob again, the green LED disappears and the power
is OFF.
CONTRAST
Used to adjust the picture contrast level.
BRIGHTNESS
Used to adjust the overall screen brightness as a compensation
for ambient light.
"+" or "-"
Press "+" or "-" to adjust the selected function.
9
E
N
The function pads:
H-Shift : to adjust the horizontal position of the image.
H-Size : to adjust the horizontal amplitude of the image.
V-Shift : to adjust the vertical position of the image.
V-Size : to adjust the vertical amplitude of the image.
SHIFT key
To select the level of function.
"Shift" LED off - Control is on first level
"Shift" LED on - Control is on second level
Second level of the function pads:
Trapezoid : to correct the trapezoid distortion of the
image.
Pincushion : to correct the barrel distortion of the image
Recall
: to recall original factory preset mode
Remarks:
1. When pressing any function pad, the "Shift" LED will flash
once to indicate the function has been selected.
2. Once the limit of the adjustable range has been reached,
the shift LED will flash continuously.
10
E
N
Adjustment
The monitor is pre-set with 8 modes for optimal display size and centering
as indicated in the following table:
Resolution Horizontal Vertical
Mode
VGA
VGA
VGA
VESA/ 75 640 x 480
VESA/ 60 800 x 600
VESA/ 75 800 x 600
VESA/ 60 1024 x 768
VESA/ 85 800 x 600
(dots x lines) Freq.(KHz) Freq.(Hz)
Remark
640 x 350
640 x 400
640 x 480
31.5
31.5
31.5
37.5
37.8
46.9
48.3
53.7
70
70
60
75
60
75
60
85
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
(A) User mode: (15 modes)
The set will save the user's setting parameters automatically.
After 10 seconds of key-pad inactivity, the LED will flash twice to
indicate the parameters being saved.
11
E
N
(B) Power Management Signalling
Power Management Definition
VESA DPMS
POWER SAVING STATES
MODE
VIDEO H-SYNC V-SYNC
POWER USED POWER SAVING(%)
ON
Active
Yes
No
Yes
No
Yes
Yes
No
No
< 70 Watts
< 15 Watts
< 15 Watts
< 8 Watts
0 %
> 82 %
> 82 %
> 94 %
Stand-by Blanked
Suspend Blanked
OFF
Blanked
Note: The video will be blanked and the power LED color will change
into following colors whenever the monitor goes into power
management status.
Green LED light
Yellow LED light
Amber LED light
- "Normal" operation
- "Stand by" or "Suspend" mode
- "OFF" mode
This monitor is Energy Star compliant when used with
a computer equipped with DPMS.
As an Energy Star Partner, MAGNAVOX, has determined that this
product meets the Energy Star guidelines for energy efficiency.
Remark:
The transition time from "on" mode to any power down mode
will take around 5 seconds.
The recovery time from "stand by" or "suspend" mode to "ON"
mode will take around 3 seconds.
12
E
N
Technical information
(I) General:
Picture tube
: 14 inch (35.5 cm), 90° deflection, non-
glare, black matrix,light transmission
57%, phosphor P22 medium short,
dotted pitch 0.28 mm.
Screen area
Recommended Display Area: 250 mm (H) x 188 mm (V)
Maximum Display Area : 274 mm (H) x 201 mm (V)
Line (Horizontal) frequency : 30 - 54 KHz (automatically)
Raster (Vertical) frequency : 50 - 110 Hz (automatically)
Mains voltage
: 100 - 240 VAC , 60 - 50 Hz
(automatically)
Power consumption
Maximum dot rate
Video input signal
Sync type
: 70 watt nominal, 90 watt max.
: 65 MHz
: 0.7 Vp-p linear / 75 Ohm
: Separate H,V, TTL level
: Positive or Negative
Sync Polarity
Pedestal
: Tilt - 5° forward, 13° backward;
swivel - 90° leftward or rightward.
Unit dimension (W x H x D)
Net weight
:
356 x 370 x 382 mm
: 10.6 Kg
Operating condition
Temperature
Humidity
: 0° C to 40° C
: 20% to 80%
Storage condition
Temperature
Humidity
: -25° C to 70° C
: 20% to 95%
DDC1/ DDC2B
: VESA standard
(II) Compatibility:
. Intel based platform (386, 486, Pentium) and other compatibles.
. VESA Guide lines and Standards.
13
E
N
(III) Pin assignment:
1
6
11
5
10
15
(1)
(1) The 15-pin D-sub connector (male) of the signal cable (IBM systems):
Pin No. Assignment
Pin No. Assignment
1
2
3
4
Red video input
9
10
11
No pin
Logic ground
Green video input
Blue video input
Identification output
- Connected to pin 10
Ground
Red video ground
Green video ground
Blue video ground
Identification output
- connected to pin 10
Serial data line (SDA)
H. Sync
V. Sync (VCLK for DDC)
Data clock line (SCL)
12
13
14
15
5
6
7
8
N Because of a policy of continuous product improvement, the above
specifications are subject to change without notice.
|