Lighting Systems LP-11
1BHFꢃꢂꢃPGꢃꢆꢃ
-JOFBSꢃ1FSG-ZUFÜꢃꢂꢁꢏꢃ ꢁꢁꢎꢅꢆDNꢊꢃ4FNJꢃ1FSGPSBUFEꢃꢆꢌ-JHIUꢃ5ꢉꢃ1FSꢃꢍꢌ'PPUꢃ /PNJOBMꢊꢃ4FDUJPO
3”
(7.62cm)
5”
(12.70cm)
Perf
13” (33.02cm)
98” (248.92cm)
2” (5.08cm)
2” (5.08cm)
2” (5.08cm)
Bottom View
Module Ordering Information
Style
Series
Options
Type
Lamps
Length
Ballast
LP
2
B
2T8
2T8 = 2F32T8
4 = 4-Foot
8 = 8-Foot
U = Universal Voltage
E = Emergency Pack
D1 = Dimming 120v
D2 = Dimming 277v
Blank = No Options
DS = A-B Switch
X4 = 4 Wire for Dimming &
Switched Emergency
Complete ordering instructions below.
Features
Ordering Information
1. Housing: 18 gauge perforated steel with 51% open hole pattern. Holes are
1/8” (0.32cm) diameter on 5/32” (0.40cm) centers. Die-formed steel end cap
with concealed access holes for through wiring. No exposed fasteners or
hardware.
Individual Fixtures:
1. Order number of MODULES required.
2. Order one POWER FEED END SET per MODULE.
Continuous Rows:
1. Determine run length.
2. Lamping: Two T8 32 watt fluorescent lamps per 4-foot section. Provided by
others.
3. Reflector: Precision die-formed specular aluminum
4. Diffuser: Opal acrylic diffuser.
2. Order the appropriate number of MODULES for the complete run.
3. Order one POWER FEED END SET per run.
4. Order one CABLE ASSEMBLY per MODULE minus one per run.
5. For runs that exceed amperage limits, order the appropriate number of SINGLE
CABLE & CORD FEEDS.
Electrical
Ballast is universal voltage, <10% THD, .88 ballast factor, instant start. 3 con-
ductor, 18 gauge wire. Color-coded quick connectors allow ease of connection
for joiner modules. For special circuiting consult factory. Cord is 18/3 SJT. Factory
installed ballast disconnect allows the ballast to be disconnected from and
reconnected to incoming power under load without turning the entire circuit off.
Dimming: 120/277 VAC, 4 wire feed required.
Finish
Powder coated baked white enamel. Custom colors available, consult factory.
Labels
UL, cUL and I.B.E.W.
Emergency Battery Pack: 32 watt: 450 lumens @ 90 minutes.
Mountings
Cable Suspension (not shown) - 4-1/2” (11.43cm) diameter flat canopy finished
white enamel, 1/16” (0.16cm) diameter stainless steel aircraft cable adjustable up
to 36” (91.44cm) without cutting. Overlap connector to provide 46” (116.84cm) of
perforated and 2” (5.08cm) solid sections contiguously without the presence of
hairline connections. (See Bottom View drawing above)
Job Information
Type:
Job Name:
Cat. No.:
Options
Dual Switching: Order the DS option for separate row switching. DS option
automatically ships with the X4 option included.
4 Wire: Order X4 modules for remainder of the run when using dimming and/or
switched emergency battery pack modules. Also, order the 4 Wire Cord Power Feed
End Sets (LP2EC36X4) when using 4 Wire Modules.
Lamp(s):
Notes:
Emergency Circuiting: Special circuiting - consult factory.
ꢀꢁꢂꢃ"JSQPSUꢃ3PBEꢄꢃ'BMMꢃ3JWFSꢄꢃ."ꢃꢅꢆꢇꢆꢅꢃtꢃ ꢈꢅꢉꢊꢃꢀꢇꢋꢌꢉꢂꢁꢂꢃtꢃ'BYꢃ ꢈꢅꢉꢊꢃꢀꢇꢍꢌꢍꢇꢂꢅ
We reserve the right to change details of design, materials and finish.
XXXꢎMJHIUPMJFSꢎDPNꢃ½ꢃꢆꢅꢅꢉꢃ1IJMJQTꢃ(SPVQꢃt #ꢅꢋꢅꢉ
|