Contents
Product Profile ............................................................................................................................................................3
EL Technology.............................................................................................................................................................3
Electrical Characteristics..........................................................................................................................................4
Connector Layout .................................................................................................................................................4
Input Connectors and Programmable Jumpers ........................................................................................5
Connectors ..............................................................................................................................................................6
Control Basics .........................................................................................................................................................6
Power Input.............................................................................................................................................................6
Display Features.........................................................................................................................................................6
Luminance Control...............................................................................................................................................6
Two-Bits Parallel ....................................................................................................................................................6
Self-Test ...................................................................................................................................................................6
Input Specifications..............................................................................................................................................7
Timing Characteristics.........................................................................................................................................7
Setup and Hold Timing.......................................................................................................................................8
Operational Specifications .....................................................................................................................................9
Environmental........................................................................................................................................................9
Reliability..................................................................................................................................................................9
Safety.........................................................................................................................................................................9
Electromagnetic Compatibility........................................................................................................................9
Optical.....................................................................................................................................................................10
Display colour..................................................................................................................................................10
Optional Filter .................................................................................................................................................10
Mechanical Characteristics...................................................................................................................................11
Installation and Handling......................................................................................................................................12
Description of Warranty ........................................................................................................................................14
Easy to Use .................................................................................................................................................................14
Ordering Information.............................................................................................................................................15
Support and Services..............................................................................................................................................15
Figures
Figure 1. EL Technology......................................................................................................................................3
Figure 2. Connector Layout...............................................................................................................................4
Figure 3. Timing Characteristics.......................................................................................................................7
Figure 4. Setup and Hold Timing.....................................................................................................................8
Figure 5. Viewing Area Chracteristics ..........................................................................................................12
Figure 6. Mechanical Dimensions .................................................................................................................13
Tables
Table 1. Input Connectors and Programmable Jumpers........................................................................5
Table 2. Connectors..............................................................................................................................................6
Table 3. Input Specifications .............................................................................................................................7
Table 4. Timing Characteristics. .......................................................................................................................8
Table 5. Setup and Hold Timing.......................................................................................................................8
Table 6. Environmental Characteristics.........................................................................................................9
Table 7. Optical Characteristics......................................................................................................................10
Table 8. Display External Dimensions..........................................................................................................11
Table 9. Display Viewing Area Characteristics ..........................................................................................11
Product Profile
The EL320.256–FD7 display is a low power, rugged, electroluminescent (TFEL)
display which replaces the bulky CRT in control and instrument product
designs. It features an integrated DC/DC converter, and its compact
dimensions save space that can allow addition of features or reduction in
overall size. It is designed to function in extreme environments, and its clear
display is viewable under most lighting conditions at wide viewing angles. Its
ease of installation reduces system integration costs.
The EL320.256-FD7 is a 320 column by 256 row flat panel display. The digital
flat panel interface is designed to match the needs of most systems.
The display requires +5 Vdc and +11 to +30 Vdc (Vcc1, Vcc2) power and four
basic signals to operate:
1. Video Data or pixel information (VID)
2. Video Clock, pixel clock, or dot clock (VCLK)
3. Horizontal Sync (HS)
4. Vertical Sync (VS)
EL Technology
The display consists of an electroluminescent glass panel and two mounted
circuit boards with control electronics.
Figure 1. EL Technology.
The EL glass panel is a solid-state device with a thin film luminescent layer
sandwiched between transparent dielectric layers and a matrix of row and
column electrodes. The row electrodes, in back, are aluminium; the column
electrodes, in front, are transparent. The entire thin film device is deposited on
a single glass substrate. The glass panel is mounted to an electronic circuit
assembly board (ECA) with an elastic spacer. The ECA’s are connected to the EL
glass panel with soldered lead frames. The result is a flat, compact, reliable and
rugged display device.
EL320.256-FD7 Operations Manual (020-0353-00A)
3
The EL320.256–FD7 display includes a light absorbing ICE ( Integrated Contrast
Enhancement) construction of the display glass. ICE construction significantly
improves the luminance contrast of the display in bright ambient. The ICE also
removes the halo around the lit pixels in dark ambient making the appearance
of each pixel extremely crisp and clear.
In the EL320.256-F Series, the 320 column electrodes and 256 row electrodes
are arranged in an X-Y formation with the intersecting areas performing as
pixels. Voltage is applied to both the correct row electrode and the
correct column electrode to cause a lit pixel. Operating voltages required are
provided by an integral DC/DC converter.
Electrical Characteristics
Connector Layout
Fig 2. Input Connectors and Programmable Jumpers.
4
EL320.256-FD7 Operations Manual (020-0353-00A)
Input Connectors and Programmable Jumpers
Table1. Input Connectors and Programmable Jumpers.
Pins
Signal
Symbol
Description
J1(Data/power input connector)
1, 2
Voltage
Vcc2
Supply voltage (+11…30V) converted to
required internal high voltages.
3, 4
5
Voltage
Enable
Vcc1
Supply voltage (+5 V) for the logic.
_ENABLE
Display operation is enabled when LOW or
left disconnected.
6,8,10
12,14,16
7
Ground
GND
TVID
Signal and power return.
Two-bit
data
Odd column data input for optional two bit
parallel mode. See page 6.
9
Vertical
Sync
VS
The vertical sync signal VS controls the
vertical position of the picture. The topmost
row displayed is the first HS HIGH time
ending after the rising edge of the VS.
11
13
15
Horizontal
Sync
HS
The horizontal sync signal HS controls the
horizontal position of the picture. The last
320 pixels before the fall of HS are displayed.
Video Clock VCLK
The VCLK signal shifts data present on the
VID and TVID lines into the display system.
VCLK is active on the rising edge.
Video Data
VID
Signal that supplies the pixel information to
the system. Even pixel data for two pit
parallel mode. See page 6.
J2 (Control input)
1
Luminance
LCb
Brightness control inputs a and b. If left
disconnected, luminance is at its maximum
level. See brightness control on page 6.
2
3
4
Luminance
Ground
LCb
GND
GND
Signal return. Same as GND in connector J1.
Signal return. Same as GND in connector J1.
Ground
Pinstrip PS1
1
SELFTEST
DCONFIG
When set, video data input in VID and TVID is displayed
asynchronously.
2
The video data is input two pixels per video clock using VID
and TVID if jumper is set.
EL320.256-FD7 Operations Manual (020-0353-00A)
5
Connectors
Table 2. Connectors.
J1
16-pin header
Mating
ODU 511.066.003.016 or eq.
ODU 517.065.003.016 or eq.
J2
4-pin header
Mating
Protector
Hirose DF1–4P–2.5 DSA or eq.
Hirose DF1–4S–2.5 R 24 or eq.
Hirose DF1–4A 1.33
Control basics
The EL panel has 320 transparent column electrodes crossing 256 row
electrodes in an X-Y fashion. Light is emitted when an AC voltage is applied at
a row-column intersection. The display operation is based on the symmetric,
line at a time data addressing scheme which is synchronized by the external
VS, HS, and video clock input signals. The signal inputs are HCT compatible
with 100 Ω series resistors.
Power Input
The input voltages needed are the +5 V input (Vcc1) for the logic and the
+11…+30V input (Vcc2) for the DC/DC converter. All high voltages required
for display glass access are generated internally.
Display Features
Luminance Control
The luminance of the display can be adjusted from below 10% up to full
brightness by a 50 kΩ external logarithmic potentiometer between LCa and
LCb control inputs (J2/1 and /2). The control function is achieved by sinking a
small current from LCa to LCb (when open, the voltages are at 5V and 0V
respectively). If the two inputs are left disconnected, the brightness is at its
maximum level.
Two-Bits-Parallel
For reduction of data clock frequency, it is possible to input the data of two
pixels per pixel clock. This feature is selected with DCONFIG jumper (PS1/2). If
the jumper is set, data for even columns is input in VID and data for odd
columns is input in TVID. If jumper is open, data is input normally to VID only.
Self Test
When SELFEST jumper (PS1/1) is set, the video data at VID and TVID are
displayed asynchronously without the use of any timing signals.
6
EL320.256-FD7 Operations Manual (020-0353-00A)
Input Specifications
Table 3. Input Specifications.
Parameter
Symbol Min.
2V
Typ.
Max.
Absolute min./max.
Logic input HIGH
Logic input LOW
Supply voltage
Supply current at 5V
Supply voltage
—
—
5.0V
0.1A
—
Vcc1
0.8V
5.25V
0.2A
30V
Vcc1 + 0.5V Abs. max.
–0.5V Abs. min.
6.0V Abs. max.
Vcc1
Icc1
4.75V
—
Vcc2
10.8V
33V Abs. max.
Supply current at 12V Icc2
@ 60 Hz
@ 120 Hz
—
—
0.25A 0.5A*
0.5A
0.9A
Power consumption
@ 60 Hz
@ 120 Hz
—
—
3.5W
6W
6W*
11W
* Values verified at design, not measured.
Operating conditions: Ambient temperature 25°C
Note: Absolute maximum ratings are those values beyond which damage to
the device may occur. The minimum and maximum specifications in this
Operations Manual should be met, without exception, to ensure the long-
term reliability of the display. Planar does not recommend operation of the
display outside these specifications.
Timing Characteristics
Figure 3. Timing Characteristics
EL320.256-FD7 Operations Manual (020-0353-00A)
7
Table 4. Timing Characteristics.
Description
Min
60
1
Max
Unit
µs
Note
T1 Vertical Front Porch
T2 VS HIGH/LOW time
T3 Vertical Blank
T4 Vertical Period
VS frequency
1
2
tVCLK
µs
40
256
tHS
Hz
120
Typ
Description
Min
1
Unit
µs
Note
3
T5 HS setup to VS
T6 HS hold from VS
T7 HS Low Time
T8 HS High Time
T9 HS period (tHS)
3
µs
4
tVCLK
tVCLK
µs
320
19
320
4
Notes:
1. This time is needed to display the last row and to initiate the following
frame.
2. Only rising edge is used.
3. 2 tVCLK minimum
4. The number of VCLK pulses during HS high time must be even.
Video clock VCLK must be kept running continuously.
Setup and Hold Timing
Figure 4. Setup and Hold Timing.
Table 5. Setup and Hold Timing.
Symbol Description
Min
8ns
Max
tSU
HS, VID, TVID setup to VCLK
tHOLD HS, VID, TVID hold from VCLK
8ns
tWL
tWH
VCLK low width
VCLK high width
VCLK period
16ns
16ns
40ns
tVCLK
VCLK frequency
25 MHz
8
EL320.256-FD7 Operations Manual (020-0353-00A)
Operational Specifications
Environmental
Table 6. Environmental Characteristics.
Temperature
Operating
–25…+65°C
Non-operating
Operating Survival
–40…+85°C
–40…+70°C (no permanent damage)
Humidity
Relative Humidity
Damp Heat
+40°C, 93% RH, Operating (IEC 68-2-3)
+25…+55°C, 95% RH, Non operating (IEC 68-2-30)
Altitude
15,000 m (50,000 ft.) above sea level
Standard IEC 68–2–13
Vibration
20…500 Hz
ASD level 0.05 g2/Hz
30 min each axis
Standard IEC 68–2–36, Random Vibration, Test Fdb
Shock
Magnitude
Duration
100 g
4 ms (half sine wave)
Number of shocks
18 (3 on each of the 6 surfaces) IEC 68-2-27, test Ea
Reliability
Safety
MTBF > 50,000 h @ 25°C, @ 120 Hz
The display will not inhibit the end product from obtaining any of the
following certifications: UL544, IEC 950.
Electromagnetic Compatibility
The display is capable of operating in an end product that complies with:
EN55022 Class B, FCC Part 15J Class B.
EL320.256-FD7 Operations Manual (020-0353-00A)
9
Optical
Determined at 25°C ambient.
Display colour
Wide band amber (ZnS:Mn) Peak wavelength 580nm typ.
Table 7. Optical Characteristics.
Areal Luminance
On Luminance
28 cd/m2 (8.2 fL) min @ 60Hz
55 cd/m2 (16 fL) min @ 120Hz
Measured at the center and the four corners of the screen.
Luminance Non-uniformity
Maximum
30%
= (1– min. luminance/max luminance) x 100.
Luminance Variation (Time)
Maximum
20%
10,000 h @ 25°C
Luminance Variation (Temperature)
Maximum
15%
over specified temperature ranges.
Luminance Contrast Ratio
MInimum
20:1
@ 60HZ, @ 500lx
@ 60HZ, @ 4500lx
@ 120HZ, @ 500lx
@ 120HZ, @ 9000lx
3:1
36:1
3:1
Viewing Angle
Minimum
160°
Illuminance
Classification
1 … 10 lx
10 … 100 lx
dark
dim
100 … 1000 lx
1000 … 10000 lx
10000 … 100000 lx
office
bright
sunlight
Optional Filter
The luminance contrast of EL320.256–FD7 is sufficient for operation without
any contrast enhancement. An anti-reflective coating or protecting sheet with
anti- reflective treatment is recommended. For best overall performance in
high ambient luminance levels, a circular polarizing filter with anti-reflecting
coating or etch is recommended. This filter will still lower the reflections from
the display background and improve the contrast ratio. Contact Planar for
details.
10 EL320.256-FD7 Operations Manual (020-0353-00A)
Mechanical Characteristics
Figs. 6 shows the mechanical dimensions of a EL320.256-FD7 display unit.
Table 8. Display External Dimensions.
Height
110 mm
4.33 in.
Width
Depth
Weight
130 mm
5.12 in.
33.0 mm
310 g max.
1.30 in.
10.9 oz. max
The EL320.256–FD7 is mechanically compatible with existing Planar
MD320.256 and EL320.256 displays
Table 9. Display Viewing Area Characteristics.
Active Area
millimeters (inches)
height
width
76.7 (3.02)
95.9 (3.77)
Pixel Pitch
height
width
0.30 (0.012)
0.30 (0.012)
millimeters (inches)
Pixel Size
height
width
0.24 (0.009)
0.24 (0.009)
millimeters (inches)
Pixel fill factor
Pixel Matrix
64%
320 horizontal by 256 vertical
CAUTION: The ambient temperature of the display should not be allowed to
exceed the environmental specifications (see page 9). In most applications, an
air gap of min5 mm is recommended (see mechanical drawings). Some
applications may require, however, a larger air gap or cooling of the display
unit in the system. Note that this may slightly increase the total depth of the
design.
WARNING: The product generates potentially dangerous voltages capable of
causing personal injury (high voltage pulses up to 195 Vac). Do not touch the
display electronics during operation!
ELECTROSTATIC CAUTION: The Planar display uses CMOS and power MOS-
FET devices. These components are electrostatic sensitive. Unpack, assemble
and examine this assembly in a static-controlled area only. When shipping
use packing materials designed for protection of electrostatic-sensitive
components
EL320.256-FD7 Operations Manual (020-0353-00A)
11
Fig 5. Viewing Area Characteristics in mm.
Installation and Handling
EL320.256–FD7 should be mounted using the four M3 corner standoffs. It is
recommended to use also the center nut in the mounting if the vibration or
shock stress is severe.
Before touching the display, necessary precaution must be taken to prevent
application of static charges on the display from the operator or tools.
The display is made of glass material and should be handled with proper care.
Do not drop the display or allow hard objects to strike its surface.
NOTE: For trouble-free data transfer a maximum cable length of 300 mm (12
in.) from data transmitter to display input connector is recommended. If
longer cables up to 2 m ( 80 in.) length are needed, a serial resistor of appr.
100 Ω could be placed at each of the four signal line outputs of the
transmitter in order to lower signal reflections.
12 EL320.256-FD7 Operations Manual (020-0353-00A)
Fig 6. Mechanical dimensions in mm.
EL320.256-FD7 Operations Manual (020-0353-00A)
13
Description of Warranty
Seller warrants that the Goods will conform to published specifications and be free from defects in
material for 12 months from delivery. To the extent that Goods incorporate third-party-owned
software, Seller shall pass on Seller's licensor's warranty to Buyer subject to the terms and conditions
of Seller's license.
Warranty repairs shall be warranted for the remainder of the original warranty period. Buyer shall
report defect claims in writing to Seller immediately upon discovery, and in any event, within the
warranty period. Buyer must return Goods to Seller within 30 days of Seller’s receipt of a warranty
claim notice and only after receiving Seller’s Return Goods Authorization. Seller shall, at its sole
option, repair or replace the Goods.
If Goods were repaired, altered or modified by persons other than Seller, this warranty is void.
Conditions resulting from normal wear and tear and Buyer's failure to properly store, install, operate,
handle or maintain the Goods are not within this warranty. Repair or replacement of Goods is
Seller’s sole obligation and Buyer's exclusive remedy for all claims of defects. If that remedy is
adjudicated insufficient, Seller shall refund Buyer's paid price for the Goods and have no other
liability to Buyer.
All warranty repairs must be performed at Seller’s authorized service center using parts approved by
Seller. Buyer shall pay costs of sending Goods to Seller on a warranty claim and Seller shall pay costs
of returning Goods to Buyer. The turnaround time on repairs will usually be 30 working days or less.
Seller accepts no added liability for additional days for repair or replacement.
If Seller offers technical support relating to the Goods, such support shall neither modify the
warranty nor create an obligation of Seller. Buyer is not relying on Seller’s skill or judgment to select
Goods for Buyer’s purposes. Seller’s software, if included with Goods, is sold as is, and this warranty
is inapplicable to such software.
SELLER DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Easy to Use
There are many options available which make Planar flat panel displays easy to use, easy to
interface, and easy to package. Call Planar for complete information.
14 EL320.256-FD7 Operations Manual (020-0353-00A)
Ordering Information
Product
Part Number
Description
EL320.256-FD7
996-5089-00
EL320.256 ICE high-bright display, Op. temp -25
- +65º C
EL320.256-FD7 AG
996-5089-01
EL320.256-FD7 with optically bonded
anti-glare film
Design and specifications are subject to change without notice.
Support and Service
Planar is a U.S. company based in Beaverton, Oregon and Espoo, Finland, with a world-wide
sales distribution network. Full application engineering support and service are available to
make the integration of Planar displays as simple and quick as possible for our customers.
RMA Procedure: Applying for a Returned Material Authorization number, please contact
Planar Systems, Inc., with the model number(s) and original purchase order number(s). When
returning goods for repair, please include a brief description of the problem, and be sure to
mark the outside of the shipping container with the RMA number.
EL320.256-FD7 Operations Manual (020-0353-00A)
15
Planar Systems, Inc.
Customer Service
24x7 Online Technical Support: http://www.planar.com/support
Americas Support
1195 NW Compton Drive
Beaverton, OR 97006-1992
Tel: 1-866-PLANAR1 (866) 752-6271
Hours: M-F, 5am - 5pm Pacific Time
Europe and Asia-Pacific Support
Olarinluoma 9 P.O. Box 46
FIN-02201 Espoo, Finland
Tel: +358-9-420-01
Hours: M-F, 7:00am - 4pm CET
© 2004 Planar Systems, Inc. 06/04 Planar is a registered trademark of Planar Systems, Inc.
ICE, ICEBrite, and ICEPlus are trademarks of Planar Systems, Inc.
Other brands and names are the property of their respective owners.
Technical information in this document is subject to change without notice.
020-0353-00A
16 EL320.256-FD7 Operations Manual (020-0353-00A)
|